Hirschmann MACH104-16TX-PoEP ethernet switches
17 August, 2011 | Supplied by: Belden Australia Pty Ltd
The Hirschmann MACH104-16TX-PoEP ethernet switches provide PoE+ capability in accordance with IEEE 802.3at standards. The switch can power 16 ports at 15.4 W or 8 ports at 30 W each, enabling users of industrial ethernet to take advantage of PoE devices.
Harvest time
12 August, 2011 | Supplied by: ABB Australia Pty Ltd
Energy harvesting is the process by which energy (ambient, motion, wind, light), derived from external sources, is captured and stored to supply power for low-energy electronics. Ambient energy is available in abundance in the process industry and it is here that energy harvesting is beginning to make its mark.
Beckhoff EL6631-0010 Profinet terminal for EtherCAT
19 July, 2011 | Supplied by: Beckhoff Automation Pty Ltd
Beckhoff is expanding its product range for the EtherCAT I/O system with the EL6631-0010 Profinet terminal which, as a gateway from EtherCAT to Profinet RT, connects two real-time ethernet bus systems with one another.
Moxa IMC-21A industrial ethernet-to-fibre media converter
18 July, 2011 | Supplied by: CrispTech Pty Ltd
The Moxa IMC-21A industrial ethernet-to-fibre media converter converts from 10/100BaseTx to 100BaseFx and is designed to meet the needs of critical applications - it can operate reliably and stably in a wide temperature range of -40 to 75°C and is housed in a rugged metal case.
Moxa PT-508/510 series IEC 61850-3 substation switches
08 July, 2011 | Supplied by: CrispTech Pty Ltd
The Moxa DIN-Rail PT-508/510 series IEC 61850-3 substation switches offer a -40 to 85°C operating temperature range, and redundant features that tackle specific needs and requirements found in power substations.
Pepperl+Fuchs intrinsically safe transmitter power supplies
07 July, 2011 | Supplied by: Pepperl+Fuchs (Aust) Pty Ltd
Pepperl+Fuchs has released four transmitter power supplies for intrinsically safe applications up to SIL3. The transmitter power supplies for the K- and H-Systems have each been extended to include two additional modules that are designed for intrinsically safe applications up to SIL 3 according to EN61508. The advantage of these supplies is that only a single transmitter is required to construct an intrinsically safe signal circuit for SIL 3. Previously for SIL 3 this was only possible using two separate inputs, both of which had to be monitored for redundancy reasons. Internal diagnostic functions are also signalled via a single output and red LED, and prescribed test intervals can be extended for SIL 2 applications.
Quatech Airborne wireless ethernet bridges and routers
05 July, 2011 | Supplied by: Interworld Electronics and Computer Industries
Interworld has expanded its range of Quatech ethernet-to-Wi-Fi products.
GarrettCom Magnum 10ETS ethernet terminal server
02 July, 2011 | Supplied by: Madison Technologies
The GarrettCom Magnum 10ETS ethernet terminal server provides up to eight ethernet ports or up to 32 serial ports for protection, SCADA devices and IRIG-B time coding, and is suitable for large substation installations with large numbers of serial instruments.
MooreHawke Trunksafe Fault-Tolerant Fieldbus System
29 June, 2011 | Supplied by: http://www.miinet.com/moorehawke
The Trunksafe Fault-Tolerant Fieldbus System from MooreHawke protects against single points of failure.
Achieving next-generation connectivity
15 June, 2011 | Supplied by: Belden Australia Pty Ltd
Industrial ethernet impacts every aspect of the operation. Building a strong industrial ethernet system and harnessing the power of its wireless component can reap unanticipated benefits for the entire facility.
Westermo Lynx+ L110-F2G managed 10-port Layer 2 ethernet switch
04 June, 2011 | Supplied by: Madison Technologies
The Lynx+ L110-F2G is a managed 10-port Layer 2 ethernet switch from Westermo that is suitable for advanced Layer 2 switching in industrial applications with extreme operating conditions. It has eight fixed 10/100/BaseTX ports and two multi-rate SFP ports (100 Mb or 1000 Mb), enabling users to choose from a variety of transceivers.
Integrating a network of wireless sensors with standard control systems
02 June, 2011 | Supplied by: Zigsense
Wireless mesh networks are designed to provide high bandwidth communications channels between wireless sensing nodes over a specific coverage area.
Turck BL20 Economy gateways for EtherNet/IP and Modbus TCP
27 May, 2011 | Supplied by: Turck Australia Pty Ltd
Turck has released the BL20 Economy gateways for EtherNet/IP and Modbus TCP. Providing a flexible in-the-cabinet system for distributed I/O, these gateways can be paired with a broad range of I/O slices to suit users’ application communications and transparency requirements. RFID can also be incorporated in any distributed I/O product by applying the necessary RFID-S slices.
Moxa IKS-G6524 Series industrial rackmount ethernet switches
25 May, 2011 | Supplied by: CrispTech Pty Ltd
The IKS-G6524 Series of high port density, industrial-grade, rackmount ethernet switches support full gigabit capability for use as centralised switches in industrial networks. They feature 24 gigabit ports or up to 24 gigabit SFP fibre connections operating at 10/100/1000 Mbps. The switches are suitable for creating high-performance aggregated connectivity for networks that support bandwidth-hungry multimedia and video applications. The IKS-G6524 series also includes three copper/fibre combinations with SFP choices.
Harting Ha-VIS FTS 3100-A, FTS 3082-ASFP and FTS 3060-A switches
17 May, 2011 | Supplied by: Harting (HK) Limited
Harting has announced three additions to its range of fast ethernet switches with Fast Track Switching technology: the Ha-VIS FTS 3100-A, equipped with 10 RJ45 ports; the Ha-VIS FTS 3082-ASFP, equipped with eight RJ45 ports plus two SFP slots; and the Ha-VIS FTS 3060-A prototype, with six RJ45 ports in a slim design.
