Pallet system
01 November, 2008 | FlexCAM
The FlexLink X85 conveyor system allows for building highly efficient lines. The system is a toolbox for single-piece flow solutions enabling flexible routing and full control of each product in process.
Bulk solid flow measurement
01 November, 2008 | SWR Engineering Messtechnik Pty Ltd
SolidFlow can be used to measure lean phase mass flow of bulk solids up to 20 t/h, either in free fall or pneumatically conveyed. It uses a microwave technique.
IEC USB-IDIO series USB isolated I/O module
01 November, 2008 | Interworld Electronics and Computer Industries
The IEC USB-IDIO series is suitable for adding portable, easy-to-install isolated input and solid-state output capabilities to any computer with a USB port. The USB-IDIO series are USB 2.0 high-speed devices, offering the highest speed available with the USB bus. A number of input and output configurations are available.
Mobile scanning computers
01 November, 2008 | Peacock Bros Pty Ltd
Intermec’s CK3 series of handheld rugged mobile computers offer improved power storage technology and durable lightweight construction.
Level measuring instrument
01 November, 2008 | Endress+Hauser Australia Pty Ltd
The Liquicap T continuous level measuring instrumentation for liquids features a build-up compensation mode that overcomes performance problems normally associated with conventional capacitance/inductance level measuring probes, particularly in chemically aggressive, sticky liquid applications.
Multifunction timer
01 November, 2008 | Eaton Electrical (Australia) Pty Ltd
The Eaton Durant E42A24M multifunction timer features an 11-pin base with two timed changeover outputs. The timer features seven multifunction modes that include on delay, off delay, single shot, percentage timer, pulse output, timing after a pulse, and timing after closing or opening a contact.
RTU for hazardous areas
01 November, 2008 | Ovarro
The Kingfisher G30 RTU has successfully completed the MET certification process for safety standards UL 1604, Electrical Equipment for Use in Class I and Class II, Division 2, and Class III Hazardous (Classified) Locations; and CSA 22.2 No. 213-M1987, Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazardous Locations.
iBase MI933 AMD M690E-based mini-ITX motherboard
01 November, 2008 | Backplane Systems Technology Pty Ltd
iBase’s MI933 AMD M690E-based mini-ITX motherboard is powered by the AMD 200U and 210U Sempron BGA processors running at 1.0 and 1.5 GHz respectively.
Compact Modbus RTU master
01 November, 2008 | Moore Industries
The microNCS Modbus RTU master and distributed I/O system can be used to send just a few, or hundreds of, process signals between the field or factory floor and a control system.
Melt pressure transducers
01 November, 2008 | Bestech Australia Pty Ltd
The MPT160, MPT161 and MPT26X series are a range of melt pressure and temperature transducers that are constructed with a full bridge strain gauge circuit and are made wholly from stainless steel material. Additionally, the pressure diaphragm features a surface treatment with special alloy coating for all models.
Rotary screw compressor
01 November, 2008 | Kaeser Compressors Australia
The DSDX rotary screw compressor range has a compact design. Motor powers of either 132 or 160 kW provide air deliveries of 24 to 30 m3/min. Both models in the range (DSDX 243 and 302) are designed for pressures up to 15 bar.
ABB Australia low-voltage AC motors
01 November, 2008 | ABB Australia Pty Ltd
ABB Australia has launched low-voltage AC motors with improved energy efficiency and life cycle value. The motors are available from 0.06 to 95 kW while the frame size starts from 56, going all the way to 250. The range is classified into three ranges: general performance, industrial performance and process performance. Frame materials include cast iron and aluminium.
Robot programming GUI
01 November, 2008 | Marand Precision Engineering
SmartGUI is the graphical user interface for Kuka robots. Robots only work on instruction and the SmartGUI system is designed to enable that instruction be straightforward and simple.
Component HMIs
01 November, 2008 | Rockwell Automation Australia
Suitable for OEMs and other industrial operators, the Allen-Bradley PanelView Component operator interface provides the right amount of control at a cost-effective price.
Sonar transducer for level control
01 November, 2008 | Hawk Measurement Systems Pty Ltd
The line of ‘fourth-generation’ sonar transducers designed for improved sensing of interface levels in clarifiers and thickeners is available. The sensors claim improvements in overall power, penetration and calibration density range. They provide better capability under high suspended solids loading, ‘sliming’ and generally upset process conditions.
